MISCELLANEOUS PRODUCTS
FILLERS
M15 FILLER
LIGHTWEIGHT HOLLOW GLASS BUBBLES
PURPOSE: For use as a high quality filler in R1 FAST CAST® resin to extend the resin, decrease the part weight, improve the physical qualities such as dimensional stability and make it possible to cast unlimited thickness (using #709) in one pour without exothermic cracking. USES: Blend with the resin 50/50 by volume to make decorative castings and our Machineable Plastic R1/M15 (a syntactic foam) which also gives it some insulation qualities. A high load of filler will turn the resin into a putty consistency. This filler has very high quality consistency, low moisture content and due to these reasons, actually makes the finished casting less expensive in the long run than using less expensive similar fillers. Quality control pays. Always keep containers closed to avoid moisture contamination. 2 Quart Box, 2 Gallon Box, 5 Gallon Box, One 10 Cubic Foot Box; (can be shipped by UPS), Bulk Sizes also in Stock
HG3000 FILLER
HEAVY SOLID GLASS MICROSPHERES
PURPOSE: For use as a very high quality filler for R1 FAST CAST® to strengthen the finished casting, increase the density, minimize shrinkage (less than 1/32" in 12", 50/50 volume blend), create a glass smooth cell structure and make unlimited thickness in one pour without cracking with FAST CAST® 709. The HG3000 FILLER is manufactured under rigid QC methods and has such a low moisture content that it will not cause resin problems as do other similar fillers. Again, this is where good quality control saves through less rejects. We have tested many brands and types of fillers and we only accept the best. USES: Blended 50/50 by volume with our #709 resin to make our Machineable Plastic R1/HG3000 composite tools, patterns, reference fixtures, vacuum forming and plug assist tools and industrial castings. 1 Quart Container, 1 Gallon Container, 5 Gallon Pail, Bulk Container
P1 Easy Green FILLER®
MEDIUM WEIGHT PLASTIC
PURPOSE: For use as a filler only with our #709 or #891 resins (50/50 ratio by volume) to make nonabrasive Machineable Plastic R1/P1. The R1/P1 is used to make prototypes and proof CNC machining. Cannot be painted. The density of the resin remains almost the same with the filler added. 2Quart Container, 2 Gallon Container, 5 Gallon Pail, Bulk Container
OTHER PRODUCTS
BARRIER COAT
Tan color. Use in RTV Silicone Rubber molds for protection, better detail and paint primer. For good quality, this is a must. Flammable liquid. 5 Gallons
RTV SILICONE RUBBER & CATALYST
For making flexible molds. Comes with complete instructions. We highly recommend this RTV as a quality product. Tin and platinum based. Sold by weight, 1 Quart Kit, 1 Gallon Kit, 5 Gallon Kit.
MOLECULAR SIEVES
A powder additive for use with R1 FAST CAST® to keep the resin from expanding or foaming due to moisture contamination. Add small amounts to the "B" side for good quality control. Sold by weight. This material has the color and consistency of talcum powder. It will feel warm to the touch. 1 Pint, 1 Quart, 1 Gallon, 5 Gallons
SMS (Silicone Mold Saver)
For use on new or old RTV Silicone Rubber molds to extend their life 25% to 75%. Non-transferring to the casting if applied correctly. A real cost savings, that more than pays for itself, especially when you need just a few more parts out of a badly deteriorating mold. The SMS gives you a fresh "skin" without loss of detail but does tend to gloss up the casting. The SMS must be sprayed only and then left to cure overnight. Recommend a dedicated airless spray gun (Wagner #200 series or equal). 5 Gallons
SPRAY CAN MOLD RELEASE
For use on original patterns prior to pouring liquid RTV Silicone Rubber . Not recommended for some types of thermoplastics or sandblasted redwood (refer to SP MOLD RELEASE). No CFC's. One 12 oz. Aerosol can, 1/2 case or One case of 12.
SP MOLD RELEASE
For use over porous patterns such as sandblasted redwood signs prior to pouring liquid RTV Silicone Rubber, works best when reduced with 85% mineral spirits to a slushy consistency. Also used on metal or plywood molds, as is, when pouring R1 FAST CAST® and filler mixture to make Machineable plastic. Similar to petroleum jelly, stable up to 400 degrees F, 1 Quart, 1 Gallon, 5 Gallons.
PIGMENTS
Black concentrates for use in the "B" side resin only, 2 - 5%. 1 Pint, 1 Quart, 1 Gallon. Other colors available.
JIFFY® MIXING BLADES
It is very important for quality control to have a complete and proper mix of resins. Ratio, method of mix, length of time of mixing and temperature are all points to consider. Follow the instructions. Quick hand mixing is usually not recommended. Stainless steel designed for fast, thorough mixing.
"U" CHANNEL KNIFE
Razor sharp, very strong, steel knife used to cut a U channel locking groove for making a split or two part RTV Silicone Rubber mold.
LARGE SPATULA
Use for RTV Silicone Rubber in the mixing bucket. A high quality rubber, molded as a single unit for longer life. Cured RTV Silicone Rubber pulls off easily. 13.75" long, blade is 3" wide x 4.5" long. After your first mix of rubber, scrape the sides and bottom of the mixing container with this spatula and then mix the rubber again using the Jiffy® Mixing blade until even color.
|
